Request a Quote

Get Started

10073 StingRay Parts Washer

Retractable Turntable Industrial Parts Washer

Jet Spray Cabinet Parts Washer StingRay SR10073The StingRay 10073 parts washer is engineered to provide the cleaning capacity to handle extremely large industrial parts cleaning loads. The impressive work area can even handle a complete Caterpillar 3516 engine in the horizontal position for pre-washing before tear down. Additional industrial parts washing applications include cleaning gear drives & cases, precision gears, and torque arms from wind turbines, cranes, bridges, mining equipment and satellite antenna drives for rebuilding and repair.

USA Specifications:

SR 10073
Parts Washer

Metric Specifications:

SR 10073
Parts Washer

Standard Features & General Construction

  • Green Technology: Closed Loop Zero Discharge
  • Swing Door Retracting Turntable for Maximum Access
  • Electronic Water Level Control & Refill
  • Oscillating Wash Manifold to Maximize Cleaning
  • Easy to Service Front Wash Pump Suction Strainer
  • Adjustable Electronic Temp Control, Temp Gauge
  • Control Transformer External of Panel minimizes Heat
  • Programmable 24 Hour 7 Day Clock
  • Low Water Shut-off Protects Pumps & Heating System
  • Electronic Door Safety Interlock
  • Wash Cycle Timer with Auto Reset
  • Heavy gauge 3/16" Sheet Steel Cabinet Thickness
  • 230 V or 460 V - 60 Hz 3-Phase with 120 V Controls
  • Chemical Resistant Two Part 3 mil Epoxy Coating
Work Area Dimensions: US Metric
Turntable Diameter: 100inches 2540 mm
Work Height: 73 inches 1850 mm

Table Load Capacity:

10,000 lbs 4530 kg
Heavy Duty Capacity: 20,000 lbs 9060 kg
Overall Dimensions: US Metric
Width: (Std Unit) 156 inches 3960 mm
Depth: (Std Unit) 132 inches 3350 mm
Height: 137 inches 3470 mm
Empty Weight: 18,000 lbs 8154 kg
Reservoir Capacity: 920 gallons 3482 liters
Duplex Reservoir: Add 47 gallons 178 liters
Sludge Capacity: 260 gallons 984 liters
Spray Blast Manifold:
OSCILLATING NON-SYNCHRONOUS Video
Angle of Oscillation: (Picture) 39 Degrees
Frequency of Oscillation: 4 per minute
Number of Wash Nozzles: (Picture) 20
Type of Nozzle: V-Jet
Nozzle Material: 316 Stainless
Heating System: US Metric
Operating Temperature: 140-190 degrees F 60-87 degrees C
Initial Heat up Time: 60-90 minutes 60-90 minutes
Electric Heat Element Size: (Picture)** 120 kW 120 kw
 Gas / Propane (Picture)  850,000 BTU/hr  249 kW
Electrical Panel (Picture) US Metric
Motor Starters: Across the Line Across the Line
Short Circuit Protection: Std Std
Overload Protection: Std Std
Electrical Enclosures: NEMA 12 IP65
Wiring Standard: NFPA 79  
Wiring Conduit: Flex-Non-Metallic Flex-Non-Metallic
Conduit Type: Liquidtight Nema 12 Liquidtight IP65
Pump System & Performance:  
Motor Type: (Picture) Energy-Efficient
Motor Rating: Continuous Duty
Motor Enclosures: TEFC

High Efficiency, Rated for continuous duty (20 Start/hour without overheating), vertical, centrifugal, seal-less, balanced, enclosed impeller. Note: All performance data taken at nozzle discharge.

Standard: 30 hp (US) 22 kW (Metric)
Total System Flow: 343 gpm 1297 l/min
Flow per Nozzle: 14.3 gpm 54 l/min
System Pressure: 121 psi 8 bar
Blast Velocity: 133 ft/sec 41 m/sec
Power Density: 0.09 hp/ft³ 2 kW/m³

 

UPGRADES: (DUPLEX) 55 hp (US) 41 kW (Metric) 70 hp (US) 52 kW (Metric)
Total System Flow: 399 gpm 1508 l/min 431 gpm 1629 l/min
Flow per Nozzle: 16.6 gpm 63 l/min 18 gpm 68 l/min
System Pressure: 163 psi 11 bar 190psi 13 bar
Blast Velocity: 155 ft/sec 47 m/sec 168 ft/sec 51 m/sec
Power Density: 0.17 hp/ft³ 4 kW/m³ 0.21 hp/ft³ 5 kW/m³

 

Results may vary based on machine configuration.
** Heating element sizes listed for 208, 240 & 480 volt systems. Sizes vary slightly for other voltages.

 

StingRay Parts Washers

HD Retractable Turntable Models
In-line Lift Door
Aircraft Wheel Washer Systems