Heavy Duty Clamshell Parts Washer
The StingRay 13648 Clamshell parts washer is engineered for heavy-duty cleaning in many applications where the load capacities exceed 20,000 lbs / 12,684 kg, such as off-road equipment, surface mining electric and diesel shovels, loaders, and steel mill component rebuilding and repair. The clamshell design provides complete access for loading and unloading industrial parts up to 82,500 lbs / 37,400 kg. The 13648 parts washer is unmatched in its high reliability, superior performance, and productivity.
Standard Features & General Construction
- Green Technology: Closed Loop Zero Discharge
- Swing Door Retracting Turntable for Maximum Access
- Electronic Water Level Control & Refill
- Oscillating Wash Manifold to Maximize Cleaning
- Easy to Service Front Wash Pump Suction Strainer
- Adjustable Electronic Temp Control, Temp Gauge
- Control Transformer External of Panel minimizes Heat
- Programmable 24 Hour 7 Day Clock
- Low Water Shut-off Protects Pumps & Heating System
- Electronic Door Safety Interlock
- Wash Cycle Timer with Auto Reset
- Heavy gauge 1/4" Plate Steel Cabinet Thickness
- 230 V or 460 V - 60 Hz 3-Phase with 120 V Controls
- Chemical Resistant Two Part 3 mil Epoxy Coating
| Work Area Dimensions: |
US |
Metric |
| Turntable Diameter: |
136 inches |
3040 mm |
| Work Height: |
48 inches |
2280 mm |
|
Table Load Capacity:
|
28,000 lbs |
12,700 kg |
| Heavy Duty Capacity: |
82,500 lbs |
37,400 kg |
| Overall Dimensions: |
US |
Metric |
| Width: (Std Unit) |
195 inches |
4953 mm |
| Depth: (Std Unit) |
153 inches |
3886 mm |
| Height: |
114 inches2896 |
mm |
| Empty Weight: |
26,500 lbs |
12,020 kg |
| Reservoir Capacity: |
1060 gallons |
4013 liters |
| Quadroplex Reservoir: |
Add 160 gallons |
Add 606 liters |
| Sludge Capacity: |
185 gallons |
700 liters |
| Spray Blast Manifold: |
| OSCILLATING NON-SYNCHRONOUS Video |
| Angle of Oscillation: (Picture) |
40 Degrees |
| Frequency of Oscillation: |
4 per minute |
| Number of Wash Nozzles: (Picture) |
32 |
| Type of Nozzle: |
V-Jet |
| Nozzle Material: |
316 Stainless |
| Heating System: |
US |
Metric |
| Operating Temperature: |
190 degrees F |
60-88 degrees C |
| Initial Heat-up Time: |
105 minutes |
105 minutes |
| Electric Heat Element Size: (Picture)** |
120 kW |
120 kW |
| Gas / Propane (Picture) |
990,000 BTU/hr |
290 kW |
| Electrical Panel (Picture) |
US |
Metric |
| Motor Starters: |
Across the Line |
IEC Type 2 |
| Short Circuit Protection: |
Std |
Coordinated |
| Overload Protection: |
Std |
Thermal Class 10 |
| Electrical Enclosures: |
NEMA 12 |
IP65 |
| Wiring Standard: |
NFPA 79 |
NFPA 79 |
| Wiring Conduit: |
Flex-Non-Metallic |
Flex-Non-Metallic |
| Conduit Type: |
Liquidtight Nema 12 |
Liquidtight IP65 |
| Pump System & Performance: |
|
| Motor Type: (Picture) |
Energy-Efficient |
| Motor Rating: |
Continuous Duty |
| Motor Enclosures: |
TEFC |
High Efficiency, Rated for continuous duty (20 Start/hour without overheating), vertical, centrifugal, seal-less, balanced, enclosed impeller. Note: All performance data taken at nozzle discharge.
UPGRADES:
| Standard: |
70 hp (US) |
52 kW (Metric) |
140 hp (US) High Flow |
104 kW (Metric) High Flow |
140 hp (US) High Pressure |
104 kW (Metric) High Pressure |
| Total System Flow: |
502 gpm |
1900 l/min |
1004 gpm |
3800 l/min |
860 gpm |
3250 l/min |
| Flow per Nozzle: |
15.7 gpm |
59 l/min |
15.7 gpm |
59 l/min |
19.9 gpm |
75 l/min |
| System Pressure: |
152 psi |
10.5 bar |
152 psi |
10.5 bar |
190 psi |
13.1 bar |
| Blast Velocity: |
156 ft/sec |
48 m/sec |
156 ft/sec |
48 m/sec |
198 ft/sec |
60 m/sec |
| Power Density: |
0.12 hp/ft³ |
3 kW/m³ |
0.24 hp/ft³ |
6 kW/m³ |
0.24 hp/ft³ |
6 kW/m³ |
Results may vary based on machine configuration.
** Heating element sizes listed for 208, 240 & 480-volt systems. Sizes vary slightly for other voltages.
