Request a Quote

Get Started

60112 StingRay Parts Washer

Heavy Duty Retractable Turntable Parts Washer

Diesel Engine Motor Cleaning Parts Washer StingRay SR60112The StingRay 60112 aqueous parts washer offers an impressive work area, parts washer power density and impact pressure to wash larger Caterpillar engine blocks and EMD locomotive blowers. The oscillating power wash manifold removes the toughest soils eliminating secondary parts washing procedures. Typical industrial parts washing applications include large diesel engine blocks and aircraft landing gear components.

USA Specifications:

SR 60112 Parts Washer

Metric Specifications:

SR 60112 Parts Washer

Standard Features & General Construction

  • Green Technology: Closed Loop Zero Discharge
  • Swing Door Retracting Turntable for Maximum Access
  • Electronic Water Level Control & Refill
  • Oscillating Wash Manifold to Maximize Cleaning
  • Easy to Service Front Wash Pump Suction Strainer
  • Adjustable Electronic Temp Control, Temp Gauge
  • Control Transformer External of Panel minimizes Heat
  • Programmable 24 Hour 7 Day Clock
  • Low Water Shut-off Protects Pumps & Heating System
  • Electronic Door Safety Interlock
  • Wash Cycle Timer with Auto Reset
  • Heavy gauge 3/16" Sheet Steel Cabinet Thickness
  • 230 V or 460 V - 60 Hz 3-Phase with 120 V Controls
  • Chemical Resistant Two Part 3 mil Epoxy Coating

 

Work Area Dimensions: US Metric
Turntable Diameter: 60 inches 1520 mm
Work Height: 112 inches 2840 mm

Table Load Capacity:

7500 lbs 3400 kg
Heavy Duty Capacity: 15000 lbs 6800 kg
Overall Dimensions: US Metric
Width: (Std Unit) 106 inches 2690 mm
Depth: (Std Unit) 91 inches 2310 mm
Height: 162 inches 4110 mm
Empty Weight: 7150 lbs 3240 kg
Reservoir Capacity: 350 gallons 1325 liters
Duplex Reservoir: Add 47 gallons Add 178 liters
Sludge Capacity: 80 gallons 303 liters
Spray Blast Manifold:
OSCILLATING NON-SYNCHRONOUS Video
Angle of Oscillation: (Picture) 39 Degrees
Frequency of Oscillation: 4 per minute
Number of Wash Nozzles: (Picture) 24
Type of Nozzle: V-Jet
Nozzle Material: 316 Stainless
Heating System: US Metric
Operating Temperature: 140-190 degrees F 60-88 degrees C
Initial Heat up Time: 120-140 minutes 120-140 minutes
Electric Heat Element Size: (Picture)** 80 kW 80 kw
 Gas / Propane (Picture) 550,000 BTU/hr 161 kW
Electrical Panel (Picture) US Metric
Motor Starters: Across the Line IEC Type 2
Short Circuit Protection: Std Coordinated
Overload Protection: Std Thermal Class 10
Electrical Enclosures: NEMA 12 IP65
Wiring Standard: NFPA 79  NFPA 79
Wiring Conduit: Flex-Non-Metallic Flex-Non-Metallic
Conduit Type: Liquidtight Nema 12 Liquidtight IP65
Pump System & Performance:  
Motor Type: (Picture) Energy-Efficient
Motor Rating: Continuous Duty
Motor Enclosures: TEFC

High Efficiency, Rated for continuous duty (20 Start/hour without overheating), vertical, centrifugal, seal-less, balanced, enclosed impeller. Note: All performance data taken at nozzle discharge.

Standard: 30 hp (US) 22 kW (Metric)
Total System Flow: 343 gpm 1300 l/min
Flow per Nozzle: 14.3 gpm 54 l/min
System Pressure: 121 psi 8.3 bar
Blast Velocity: 133 ft/sec 41 m/sec
Power Density: 0.16 hp/ft³ 6 kW/m³

 

UPGRADES: (DUPLEX) 55 hp (US) 41 kW (Metric) 70 hp (US) 52 kW (Metric)
Total System Flow: 399 gpm 1510 l/min 431 gpm 1630 l/min
Flow per Nozzle: 16.6 gpm 63 l/min 18 gpm 68 l/min
System Pressure: 163 psi 11.2 bar 190 psi 13.1 bar
Blast Velocity: 155 ft/sec 47 m/sec 168 ft/sec 51 m/sec
Power Density: 0.3 hp/ft³ 7 kW/m³ 0.38 hp/ft³ 9 kW/m³

 

Results may vary based on machine configuration.
** Heating element sizes listed for 208, 240 & 480 volt systems. Sizes vary slightly for other voltages.

 

StingRay Parts Washers

HD Retractable Turntable Models
In-line Lift Door
Aircraft Wheel Washer Systems