STINGRAY PARTS WASHER
The STINGRAY Parts Washer is a feature rich industrial parts cleaning system. Enclosed in a steel or stainless steel cabinet, the aqueous based washer cleans in automatic cycles. The parts wash load is placed on a powered turntable that retracts from the enclosed cleaning cabinet when the door opens. The pump system forces solution through oscillating nozzles that blast the parts load from continuously varied angles of attack. Completing the parts washer are the solution level management system, temperature controlled solution heating system, pump suction filter, safety devices, and single point connection electrical system. Optional rinse, steam exhaust and blow-off cycles are easily included per your needs. A number of optional solution maintenance devices – oil skimmer, sludge scraper, surface scraper, in-line filtration extend solution life. The StingRay Parts Washer is environmentally safe with a closed-loop, zero discharge design to meet EPA, OSHA regulations and GREEN TECHNOLOGY.
 |
PUMP SYSTEMS: All STINGRAY Simplex and Duplex Pumps, 20 horsepower and larger, are high efficiency Industrial Grade centrifugal without metal-to-metal contact in the wet end, rated for continuous duty and multiple starts, vertical mounted seal-less design, with impellers capable of passing 1/2 inch solids and balanced to within .0074 inch ounces/ounce, hardened steel pump shaft sleeves and hardened stainless steel throttle bushings, and bearings rated for 50,000 hours Barrel style Motor-to-Pump mounting and flexible coupling ensures positive alignment and reliability without periodic adjustment.
- PUMP MOTORS: TEFC with Class F Insulation and NEMA MG-1 Rated, with 1.15 to 1.25 Service Factors, Ball bearings, continuous duty Industrial Grade and rated for 20 starts/hour without overheating.
- PUMP SUCTION STRAINER: Perforated 16 ga sheet steel strainer, located at front of machine reservoir for ease of service and cleaning, designed for 2 times rate flow at 50% plugged condition.
- SUCTION STRAINER: Pore size of Pump Suction Strainer is slightly smaller than orifice diameter of nozzles, so particles that pass through the Suction Strainer will also pass through the nozzles to minimize clogging.
|
|
StingRay Parts Washer Pump |
| |
|
| |
|
|
 |
|
SPRAY MANIFOLD: Patented oscillating manifold system blasts from the top down, bottom upward, and across the cabinet. As the wash load rotates, the Manifold oscillates on its vertical axis, making a 40-degree sweep and return every 15 seconds, throughout the wash cycle. (VIDEO) Movement of the Manifold is not synchronized to rotational speed of the turntable so each surface of wash load is blasted from a different angle each time it passes the Manifold. System is driven by a TEFC gear motor with heavy-duty crank arm linkage system featuring mono-ball bearing construction for long service life. Unions or flanged connections make servicing easy.
- NOZZLE SYSTEM: High impact stainless steel machined V-Jet and “0” degree patterns, aimed and spaced for overall coverage and set so each nozzle blasts on its own plane and cannot intersect with, or deflect, other nozzles in system.
|
| StingRay Power Blast Manifold |
|
| TURNTABLE & DRIVE SYSTEM: A heavy steel turntable on sealed bearings is driven by a thermoplastic sprocket that positively engages the turntable teeth to prevent slippage. The sprocket is powered by a TEFC gear reduction motor with steel gears and ball bearings mounted externally of the wash cabinet. The drive system is protected by a clutch overload for reliability and long service life should the turntable jam from parts that may fall. The turntable is constructed of heavy bar steel with hook and eye attachments and a rim that provide for easy anchoring of part wash loads. |
|
 |
| |
StingRay Turntable Drive |
CLOSED LOOP CLEANING - ZERO DISCHARGE: During cleaning cycle no cleaning solution discharges cabinet for treatment or disposal. Complies with Federal goal of Waste Minimization and Green Technology.
AUTOMATIC WATER LEVEL SENSOR: Electronic system with large diameter stainless steel float ball, reads solution levels.
- OVERFLOW PROTECTION: Shuts off water fill to prevent flooding of shop.
- LOW SOLUTION SHUTOFF: If incoming fresh water service is interrupted, disables heat source to reduce fire hazard, and disables Pump System to prevent damage.
- AUTOMATIC WATER REFILL: Maintains solution at nominal operating level.
ELECTRICAL POWER: 230VAC or 460VAC 3-phase 60 Hz with 120VAC single-phase transformer for controls. Other voltages are available in 60 Hz and 50 Hz.
ELECTRIC OR STEAM HEATING SYSTEM: Sized per machine reservoir volume to provide 2-hour heat-up and 175°F operating temperature.
 |
|
ELECTRICAL CONTROL SYSTEM: All electrical components are UL Listed and designed to meet ANSI/NFPA-79 Electrical Standard for Industrial Machinery. All wiring runs are encased in flexible conduit and sealed with moisture proof seals and fittings inside of NEMA 12 Panels, junction boxes and electrical devices. A transformer for single phase control power is mounted in a separate enclosure to reduce heat in the main electrical panel. The wire is 14 gauge THHN stranded industrial grade throughout the system. All operator controls are identified by an engraved name plate corresponding to the wiring schematic diagram. |
|
 |
- 7-DAY PROGRAMMABLE ELECTRONIC CLOCK: Programmable dual channel Clock to preheat Power Washer only during normal wash days. Has override feature to operate Power Washer on normal off days. Provides automatic timed operation of optional Oil Skimmer.
- ADJUSTABLE THERMOSTAT & CONTROLLER: Automatically maintains solution-operating temperature. Controller is easy to adjust with Fahrenheit and Centigrade scales. Also included is an externally mounted temperature gage for measuring solution temperature.
- WASH CYCLE TIMER: Heavy Duty Industrial Eagle Signal timer with large easy to change adjustment. 0-30 minutes in 1-minute increments. Automatically resets to last wash time setting.
- STOP: Prominently mounted red Stop Button, immediately shuts down cleaning cycle functions when pressed.
- DOOR SAFETY INTERLOCK: Automatically shuts down Cleaning Cycle when Loading Door is open. Interlock relay checks safety circuit for faults each cycle by requiring loading door to open and close to reset. Guard covering switch prevents accidental operation and prevents manual override of switch.
|
7-Day Clock
Wash Cycle Timer
|
Temperature Controller
Door Safety Interlock
|
CABINET CONSTRUCTION:
| |
WALL MATERIAL: 7 gage and 1/4 inch ASTM graded sheet steel.
|
| |
STRUCTURAL MEMBERS: ASTM A-36 (minimum) structural carbon steel with 3/8 to 1 inch wall box tubing and angle engineered for the load rating of Power Washer with a margin of safety of 3 (min).
|
| |
CABINET WELDING: All seams are continuous MIG welded with E-70 electrode for strength and integrity, and to eliminate cabinet leaks without gaskets or caulking. |
| |
LEVELING BOLTS: Leveling Bolts located in four corners of base are provided to facilitate leveling of Power Washer without material handling or other equipment. Tie-down anchoring points are provided to secure the washer to the plant floor. |
 |
| |
DOOR: Ball bearing door pivot points allow for easy door opening and closing with heavy turntable loads. Door position lock holds door firmly in loading position for simple loading. Heavy-duty toggle latch securely locks door shut. Steel to Steel compression seals keep solution and steam inside cabinet without Elastomeric seals that can deteriorate from heat and chemical.
|
| |
FINISH: The entire exterior of the machine is stripped of all mill scale and welding splatter by mechanical means. Visible nicks, gouges, grinding marks are sanded smooth. All visible rust is removed. The entire surface is thoroughly cleaned with a surface preparation and solvent, twice. The finish coating consists of an acid etch primer coat followed by 2 part high build polyamide epoxy coating, 3.5 mills (min) dry film thickness. After curing for several days, the durable epoxy surface is highly resistant to alkaline detergents and extremely tough. |
|
| |
QUALITY ASSURANCE:
Every StingRay parts washer is required to pass through over 1,000 quality assurance check points, including filling each parts washer with water not once, but twice. Each Parts Washer must complete a 90 minute endurance leak tightness test on all joints before it is painted. Then we drain the parts washer, complete the construction, re-fill the solution reservoir and put the parts washer through three 30-minute wash cycles and a thorough 4 hour inspection process before it leaves the factory. During the comprehensive review all pertinent parameters are measured and recorded. The complete inspection blueprint verifies the machine meets 100% of STINGRAY requirements prior to shipment. Our goal is to make high-performance parts washers that exceed our customers’ expectations for quality and reliability. |
Parts Washers 